Sodium Bisulfate vs Muriatic Acid: Which pH Reducer to Stock
Dry acid and muriatic acid do the same job in pool water. Both lower pH and total alkalinity, the water's buffer that holds pH steady 7. So choose by customer and by warehouse, not by which one seems stronger.
Muriatic acid is a fuming liquid. Dry acid comes as granules that are easy to store, measure and sell.
We supply dry acid, also sold as sodium bisulfate or pH minus.
- Dry acid also serves service routes, dosed by the label, and pump-fed public pools, where it is dissolved first and then fed 11.
- Lead with dry acid for retail customers, spas and small pools.
- Compare prices per equal dose, because a bag and a jug hold very different amounts of acid. The dose math is below.
- Muriatic acid ships as UN 1789, Class 8 1. A UN number is the four-digit shipping ID, and Class 8 is the hazard class for corrosives. Dry acid ships under the entry on its safety data sheet (SDS); ours gives UN 1759, also Class 8 6.
The short answer: which acid for which customer
Pick by who buys and where you store it. We would use this rule to build the pH reducer part of a Water Balance range.
- Commercial pools: feed dry acid as a solution through the pH feeder. Service routes on other pools: dose it by the label. Public pools dose acid with a pH feeder, a small pump. Where a state or county follows the US model pool code, public pools must have one 8. Dry acid is put into solution before a pump feeds it 11, so the site dissolves it first and the feeder takes it from there. On other pools, service techs dose it by hand as the product label directs. Buyers who chlorinate with cal hypo (calcium hypochlorite, a dry chlorine) need a pH reducer as well. See why cal hypo customers need a pH reducer.
- Retail homeowners, spas and small pools: lead with dry acid. It is easy to measure by the scoop. It sells in small sealed tubs. And it puts no fumes on the shop floor. Ours is listed as Sodium Bisulphate (pH Minus).
- A warehouse that cannot hold corrosive liquids: start with dry acid. It still goes on a dry, sealed shelf away from chlorine. What it saves is the spill trays and non-metal racks a liquid acid needs.
- Two cases to check before any of the dry-acid rules above (rules 1 to 3). First, plaster, tile and other cement-based pools. UK guidance says to use dry acid only in pools built with sulfate-resistant cement 10. Our dry acid fits these pools once the builder confirms that; otherwise, follow the builder's advice. Second, salt pools. Start with the cell manual for every salt pool, whatever its finish, because it covers the cell itself, not the pool surface. Where it allows dry acid, lead with our dry acid; it is easy to carry and store, so it suits owners who would rather not keep a liquid acid at home. A salt pool with a cement finish needs both checks: the cell manual allows dry acid, and the builder confirms sulfate-resistant cement. Our dry acid fits only when both hold. Where the cell manual advises against dry acid, follow the acid it names; where the builder has not confirmed the cement, follow the builder's advice.
- Selling to both groups? Dry acid covers both. Sealed tubs suit the retail counter, and bulk bags suit service accounts and sites that dissolve it for a feeder 11.
| Dry acid | Muriatic acid | |
|---|---|---|
| Form | Granules | Liquid |
| Strength | 95% min purity (our spec) | Varies; read the jug |
| Equal dose | 10.5 to 11 lb 9 | 1 gal at 31.5% 4 |
| Fumes | None in storage | Strong grades fume |
| US shipping | Per its SDS (ours: UN 1759, Class 8) 6 | UN 1789, Class 8 1 |
| Leaves in water | Sulfate 11 | Chloride 11 |
| Best fit | Retail, spa, small pools; pump feeders once dissolved | Sites set up to feed liquid acid |
To use the table, name the customer group first. Then check whether you can store a corrosive liquid, and read the last row.
Three things are the same for both acids:
- Effect. Both lower pH and total alkalinity 7.
- Chlorine. Both give off chlorine gas if mixed with chlorine products 11.
- Rules. The US model pool code lists both as approved for pH control, if the product is certified to NSF/ANSI 50 or 60, the US standards for pool and drinking-water treatment chemicals 8.
Same job, two forms: what dry acid and muriatic acid are
Granular pH minus or pH decreaser is usually sodium bisulfate, also called dry acid. Liquid pH decreasers are a different product, so read the label. Our product page lists sodium bisulfate under the alias PH Minus 5. It is a dry acid, a crystal or powder that is generally white 11. In water it turns acidic and releases the hydrogen ions that lower pH 3.
Muriatic acid is the trade name for hydrochloric acid. It is hydrogen chloride, an acidic gas, dissolved in water 2. Stores sell it as a liquid in jugs.
Both lower pH. Both also lower total alkalinity. Total alkalinity is the water's buffer, the part that holds pH steady. The acid reacts with bicarbonate in the water, and that lowers the buffer 7.
So is dry acid gentler? Only in handling. It goes in by the scoop, which is easy to control and carry. In the water it is still an acid, and it lowers pH and total alkalinity too.
The US model pool code lists muriatic acid and sodium bisulfate among the approved chemicals for pH control 8. The same code also requires any chemical used for pH adjustment to carry the NSF/ANSI 50 or 60 certification named at the top 8. So where a state or county follows that code, a public-pool buyer checks that certification for whichever acid it buys. Public pools still follow their own state code.
Both acids push pH down. A customer who needs to raise pH is on a different shelf: see soda ash as the pH increaser.
How much dry acid matches a gallon of muriatic acid
A gallon of muriatic acid matches a big heap of dry acid, so prices only compare per equal dose.
One gallon of standard muriatic acid does about the same work as 10.5 to 11 lb of dry acid 4. Here, standard means the 20 °Bé grade (degrees Baumé, a density scale for acid strength), 31.5% acid, used in the working below. So compare prices per equal dose, not the price of a bag against the price of a jug.
Why does this matter? A bag-to-jug comparison can make dry acid look far cheaper, or far dearer, than it really is.
- Start with the liquid. Muriatic acid strength can be given in °Bé. US Coast Guard chemical data (CHRIS, 1999 edition) lists grades of 18, 20 and 22 °Bé 4. Those are 27.9%, 31.5% and 35.2% hydrochloric acid. We use the middle grade, 31.5%, for the example.
- Weigh the gallon. On the US standard Baumé scale, a 20 °Bé acid has a specific gravity of 145 ÷ (145 − 20), or 1.16 9. Specific gravity compares its weight with water. So one gallon weighs about 4.39 kg and holds about 37.9 mol of acid. A mol is a fixed count of molecules, used to match one acid with another.
- Match it with dry acid. Each unit of sodium bisulfate gives one unit of acid. So about 10.0 lb of pure sodium bisulfate matches that gallon 9.
- Allow for real purity. Our contract specification is 95% minimum sodium bisulfate. At that strength, the working below gives about 10.6 lb. In practice, allow about 10.5 to 11 lb of product per gallon.
Working: 3.785 L × 1.16 kg/L × 31.5% ÷ 36.46 g/mol ≈ 37.9 mol of acid. Then 37.9 mol × 120.06 g/mol ≈ 4.55 kg, or about 10.0 lb of pure sodium bisulfate. At 95% that is about 10.6 lb. 4 9
Weaker jugs need less dry acid to match. If a jug is weaker, each gallon carries less acid. So the dry-acid match drops roughly in step with the strength on the label. Then you ship more jugs, more freight and more packaging for the same dose.
One number you may see does not fit. The annex to the US model pool code gives two doses per 10,000 gallons. Either 1.6 lb of dry acid or 1.3 quarts of muriatic acid lowers total alkalinity by about 10 ppm 7. (ppm means parts per million.) Read as a ratio, that is only about 4.9 lb of dry acid per gallon. That is half the chemistry above, and the annex does not say what acid strength it assumes. So it is no basis for comparing prices. Actual dosing follows each product's label.
Tip: convert before you set shelf prices. Put the equal-dose figure on your price sheet, next to the strength printed on each jug you stock. Staff then quote both lines on the same basis, which protects your margin.
Fumes, storage and shipping: where they really differ
Liquid acid in a vented cabinet on spill trays, dry acid in closed tubs on its own shelf, and chlorine products kept apart behind a wall.
For a distributor, the real gap between these two sits in the warehouse and on the freight booking.
Storage: fumes against caking
Muriatic acid is a corrosive liquid. Diluting it can give off heat 2. Strong grades, up to 35%, fume in the air, smell sharp and are more dangerous to handle 11. It also attacks metal. It reacts with many metals, such as aluminum, zinc, iron and tin, and gives off flammable hydrogen 2. So it needs a vented area, spill trays, racks that are not metal, and staff trained to handle liquid acid.
Dry acid does not fume, but it is still an acid. It pulls water from the air, so containers must stay tightly closed 6. An open tub cakes into a hard lump.
Shipping: a named entry against an SDS entry
This is where the two part ways most. The Class 8 label and the UN number from the top of this guide decide the packaging and the booking.
Muriatic acid is simple. The US Hazardous Materials Table lists hydrochloric acid by name, as UN 1789, Class 8 1.
Dry acid is less simple. The only entry that names bisulfate is a general one for bisulfate solutions, UN 2837 1. Solid sodium bisulfate has no entry of its own. A solid that meets the Class 8 test ships under a general entry. Examples are UN 3260 and UN 1759 1.
Which entry applies? The supplier's safety data sheet (SDS) says so in Section 14. Our SDS gives UN 1759, Class 8, packing group II 6. Packing group II means medium danger within the class. We checked again in October 2026, and that entry has not changed.
So two dry-acid offers can ship under different entries. The entry sets the packaging, the labels and the freight cost.
Tip: ask for the SDS transport section before you quote freight. When you import solid dry acid, read the UN entry and packing group in the supplier's SDS. Confirm them with your forwarder before you book. That avoids relabeling, a rebooked container or cargo held at the port.
Keep both away from chlorine
Either acid mixed with hypochlorite, the chlorine in cal hypo and liquid bleach, gives off chlorine gas 11. San Francisco's public health pool page puts it plainly. Pool chlorine and pool acid mixed together make chlorine gas, which can kill if breathed in 12. Our SDS says the same for dry acid. It warns against mixing dry acid with hypochlorite bleach, ammonia cleaners or similar products 6.
For anyone who blends or co-packs, keep pH minus and cal hypo as separate products, packed separately and stored apart. For full storage rules, see keeping dry acid away from oxidizers.
What each acid leaves in the water
Each acid leaves something behind, and the two behave differently over a season.
Dry acid adds sulfate with each dose. So check sulfate in the routine water test, and keep it below 360 mg/L, the level UK guidance sets 11. (mg/L means milligrams per liter.)
In cement-finished pools this is the figure to watch, because above 360 mg/L sulfate can attack cement grout and cement 10. UK guidance advises dry acid only for pools built with sulfate-resistant cement, so confirm that with the builder first 10. The 360 figure is UK guidance. Use it as a reference point for US customers, not as their law.
Muriatic acid leaves chloride. UK guidance notes chloride can attack metal fittings if it is allowed to build up 11.
Salt pools need a second look. A salt pool makes its own chlorine from salt, in a cell called a salt chlorinator. For every salt pool, whatever its finish, check the cell manual first, because it covers the cell itself, not the pool surface.
Where it allows dry acid, our dry acid is the easy pick, because it is simple to carry and store. Where the manual advises against dry acid, follow the acid it names. If the finish is cement, the cement rule above applies as well: our dry acid fits only when the cell manual allows it and the builder confirms sulfate-resistant cement. For more, see dry acid in salt pools.
Vinyl and fiberglass pools without a salt cell can use either acid, so the customer and warehouse rules at the top decide.
Answering the acid questions customers bring to the counter
Your staff will hear the same few questions. Each answer below is short enough to say at the counter.
- Customer: Is dry acid gentler on the pool? You: Only in handling. It goes in by the scoop, which is easier to control. Why: in the water it still lowers pH and total alkalinity, as the section on what the two are explains.
- Customer: Can one replace the other, cup for cup? You: No. Follow the label on the product you bought. Why: the two doses differ a lot by weight; the equal-dose section shows how much.
- Customer: Which one suits a salt pool? You: First check your cell manual. If it allows dry acid, our dry acid, because it is easy to store. If the manual advises against dry acid, follow the acid it names. Then ask about the pool surface: for plaster or other cement, also check answer 4. Both must hold before you recommend our dry acid. Why: the cell maker writes the manual for its own cell, so follow it.
- Customer: The pool is plaster. Which one? You: Was it built with sulfate-resistant cement? If yes, our dry acid fits. If not, follow the builder's advice. If it is also a salt pool, the cell manual must allow dry acid as well (answer 3). Why: the sulfate risk to cement grout, set out in the residue section.
- Customer: Can the acid sit next to the chlorine? You: Keep them on separate shelves, and sell them as separate products. Why: the chlorine gas risk, set out in the storage section.
Spa and hot tub buyers are natural dry-acid customers. They dose by the scoop, and a small sealed tub suits them. For tubs run on bromine, see pH control in bromine tubs.
Tip: ask about the pool before you recommend an acid. Train staff to ask the questions behind answers 3 and 4 before naming a product. It takes a moment at the counter and saves you a grout or cell complaint later.
Tip: keep bulk bags off the retail counter. Hold bulk bags for service accounts and put only sealed tubs or boxed packs out front. Sealed packs keep damp air out, which cuts caked product and returns from torn bags.
What to ask for when you buy dry acid
A good inquiry gets quotes you can compare line by line. Name these items:
- Assay. This is how much of the product is really sodium bisulfate. Ask whether the figure is a contract minimum or one batch result. Our contract specification is 95% minimum sodium bisulfate.
- Iron, insolubles and chloride. Ask for a contract limit on each. Insolubles are the bits that do not dissolve in water. Our limits are iron 0.005% maximum, water-insoluble matter 0.03% maximum and chloride 0.05% maximum. Low iron matters because iron can stain light pool finishes.
- Form. Our specification is for granules.
- Pack sizes. Our product page lists standard packs of plastic drums from 0.5 to 50 kg, 25 kg bags and 1,000 kg bags 5, and other packing can be made to order. Small drums suit retail. Big bags suit repackers and service buyers.
- SDS. Ask for the current one with the quote, and check its shipping entry against the shipping part above. SDS files are reissued from time to time. Ours on file was last updated in May 2023 6.
- COA. A certificate of analysis (COA) is the lab result for one production batch. One batch on COA KX-2-24108 tested 95.5% sodium bisulfate. That result belongs to that batch, so ask for the COA of the batch you buy.
- Minimum order. One container load. We ship our dry acid by the whole container only.
- Booking. Sodium bisulfate and soda ash do not share a container. An order of pH Minus and pH Plus is two bookings.
You can send your own third-party inspector to the container loading.
Tip: write the assay into the purchase contract. Copy the assay from the quote into the contract as a minimum the shipment must meet. That keeps you from paying for a grade the shipment does not meet.
Tip: ask your forwarder for two bookings at once. Request both freight quotes together when pH Minus and pH Plus are in one order. That avoids a rejected booking or a reworked load plan.
Tip: name the inspector and the loading date in the order. Do it when you confirm a first order with a new supplier. A short or wrong load then shows up at the port of loading, not after it lands.
The rule to give your sales team
Both acids do the same job, so choose by customer and by warehouse. Dry acid is the pick for retail, spa and small-pool buyers, and it serves service routes, dosed by the label, and pump-fed public pools once dissolved 11.
Then keep two habits. Compare prices per equal dose rather than per bag or per jug. And check the SDS shipping entry before you book freight.
For more side-by-side guides, see Product Guides & Comparisons.
References
- eCFR: 49 CFR 172.101 Hazardous Materials Table — 2026-10-21
- NOAA CAMEO Chemicals: Hydrochloric acid, solution
- NOAA CAMEO Chemicals: Sodium bisulfate, solid
- USCG CHRIS: Hydrochloric acid (HCL) (June 1999 edition) — 1999-06
- Kingnod: Sodium bisulphate (PH Minus) product page
- Kingnod: MSDS of sodium bisulphate — 2023-05-21
- CDC Model Aquatic Health Code, 5th Edition (2024) Annex — 2024-12-16
- CDC Model Aquatic Health Code, 5th Edition (2024) Code — 2024-12-16
- US Bureau of Standards Circular 59: United States Standard Baumé Hydrometer Scales (1916) — 1916-04-05
- PWTAG Code of Practice (July 2021) — 2021-07
- PWTAG Technical Note 40: Choosing an acid pH correctant — 2018-09
- City and County of San Francisco: Water Chemistry (pool guidelines) — 2026-02-19


