How to Choose Pool Chemical Packaging: Drums, Pails, Bags or Retail Packs

How to Choose Pool Chemical Packaging: Drums, Pails, Bags or Retail Packs

Pick each pool chemical's pack by who opens it next. If you repack it or sell to pool service firms, import drums and bags. If it goes straight to a store shelf, have the factory fill pails, tubs or boxes.

We supply these products in the packs below and fill to the pack you choose. This is how we would make the call with you.

  • Repacking locally makes sense if you have a filling site, carry few products, or change labels often.
  • Soda ash can travel in bags. Cal hypo by sea goes only in drums or boxes.
  • Trichlor, dry dichlor, cal hypo and sodium bisulphate are in Packing Group II, the middle hazard group. Their packs need a UN test mark with X or Y.
  • Send one pack spec with liner, pallet and label details before the order.

The short answer: choose the pack by who opens it next

Think about the next pair of hands. A pool service firm opens a big drum and doses from it. A shop customer picks up a small pail and takes it home. One product can go either way. So the choice belongs to each product line, not to the whole order.

The range is wide. Our TCCA page lists 50 kg fibre drums, plastic drums from 0.5 to 50 kg, and 25 kg or 1,000 kg bags 14. The same page lists boxed retail packs 14. We also pack into small packages to the buyer's specification 10.

Then the rules narrow it. Some products ship as dangerous goods, and those need tested, marked packs. Section 14 of each product's SDS, the supplier's safety data sheet, tells you which ones. The product section below covers them one by one.

Settle packs only with a supplier you have already checked. Our checks before you shortlist a manufacturer come first.

Bulk to repack, or shelf-ready from the factory: how to decide

If you sell to service firms, import drums and big bags and resell them whole. Local repacking tends to pay when you run your own filling line, carry few products or change labels often; weigh these, they are not conditions that must all hold. Buy factory-filled packs when the product goes to retail and you have no filling site. Do the same for dangerous goods you would rather not open again.

Repack means filling bulk product into smaller packs after it lands. Shelf-ready means packs that can go on a shelf as delivered.

Your situationBulk drums and bagsFactory-filled packs
You sell to service firmsResell wholeExtra cost
You sell to shopsNeeds a filling siteGood fit
Labels change oftenGood fitReprints
Few products, big volumesGood fitAlso fine
Dangerous goodsYou open them againStay sealed

Read the table row by row. Service firms want big packs, so you resell drums and bags as they arrive. Shops want small packs, so bulk works only if you can fill and label them yourself. Frequent label changes favour bulk, because a factory-filled run means printed packs. Dangerous goods favour factory filling, because every opening is handling you must manage.

There is a middle step for tablets. We list 1 kg bags or pots packed inside 10 to 50 kg drums 14. You get small units without opening a big drum.

Bulk transport forms are not open to every product: by sea, cal hypo may not go in IBCs, large packagings, portable tanks or bulk containers 5. That is about the transport form, not about buying big drums to repack. The next section shows the packs it can use.

Compare total cost, not price per kg. Add the pack price, net product per container, freight, damage, and your own labour and labels. If factory filling is the better fit, see the pack formats we fill.

Tip: price the repack before you choose bulk. When bulk looks cheaper per kg, add local labour, empty packs, labels and losses to it. You avoid choosing bulk for a saving that is not there.

What each product can ship in

Start with section 14 of each product's SDS. It says whether the product ships as dangerous goods. That decides which packs are allowed. Then match the pack to the product.

ProductTransport statusWhat the pack must be
Soda ashNot dangerous goodsAny compatible, sealed, moisture-tight pack
Sodium bisulphateUN 1759, Class 8UN-rated for Group II
Trichlor, dry dichlorDivision 5.1UN-rated for Group II
Dichlor dihydratePer its SDSPack to match its SDS
Cal hypoDivision 5.1UN-rated; no bags by sea
PQ (liquid)Ordinary goodsAny compatible, sealed pack
DDAC (liquid)Per each grade's SDSPer its SDS group

Soda ash is the easy case. Our page lists it in 25 kg or 1,000 kg bags on pallets as standard 13, and pack and specification are made to your requirements 10. A bulk bag is a large woven bag lifted by its loops.

Sodium bisulphate looks the same on our list 6. It is not an oxidizer. But our MSDS lists it as UN 1759, Class 8, Packing Group II 7. So its bags and drums must be UN-rated for that group.

Liquids run from small bottles to tanks. Liquid polyquat (PQ) is listed in 1 to 5 L bottles packed in cartons 11. It also comes in 25 kg and 200 kg drums and 1,000 kg IBC tanks 11. An IBC is a caged plastic tank on its own pallet. Our DDAC page offers bulk and custom packs 9.

The two liquids ship differently. We ship PQ as ordinary goods. We ship DDAC as dangerous goods, under the UN entry on each grade's SDS, and the SDS shipped with the goods is the one that applies. So DDAC drums and IBCs follow dangerous-goods packing rules for the group on its SDS.

For pack options on our main chlorine, see our TCCA 90% pack options.

Dangerous goods: trichlor, dichlor, cal hypo and sodium bisulphate

An oxidizer is a chemical that can feed a fire. Packing Group II is the middle of three hazard groups. It sets how strong the pack must be.

The US hazmat table lists dry trichlor as Division 5.1, UN 2468, Packing Group II 3. Its packs carry the oxidizer label 1. Dry dichlor is UN 2465, Division 5.1, Packing Group II 2. Hydrated cal hypo is UN 2880, Division 5.1, and the US table has a Packing Group II entry for it 3.

Dichlor depends on its form. The dihydrate form is not a Division 5.1 oxidizer under US transport rules; only the dry form is UN 2465 3. Whatever the route, section 14 of the SDS for the grade you buy gives the dihydrate's transport class, and its pack follows that class. Our guide to UN numbers for pool chlorine has the codes.

Cal hypo is strictest by sea. Woven, plastic-film and paper bags are not allowed for it 5. Nor are IBCs, large packagings, tanks or bulk 5. Our cal hypo page lists plastic drums from 0.5 to 45 kg and boxed packs as standard 8, and our product pages say packing is made to the buyer's requirements 10. So by sea it goes in drums or in boxed packs 8.

A marine insurer's guidance from 2011 has cal hypo at sea packed at 45 kg or less per package, and carriers add their own advice on size. The carrier's own rules have the final say. Our standard calcium hypochlorite drums stay within that size 8.

Reading the UN mark, and the proof to ask for

A conventional blue-lid pail illustration beside an example UN packaging code and its component meanings.

The code describes packaging tests; suitability still depends on the chemical and transport rules.

A UN mark is a short code the pack maker prints or moulds on the drum or pail. A pack sold as UN standard must carry it 4. Read it in order, then check one letter.

Read the mark in order

  1. The UN symbol.
  2. A code for the pack type and material, such as a plastic drum or a fibre drum.
  3. A letter: X, Y or Z.
  4. For solids, the maximum gross mass in kg, followed by the letter S. Packs for solids show S where liquid packs show a test pressure 4.
  5. The last two digits of the year the pack was made 4.
  6. The country, then the name or symbol of the maker or approval agency 4.

The letter is the part that matters. X means the design passed Packing Group I, II and III tests. Y means the design passed Packing Group II and III tests 4. Z means Packing Group III only, so it is not enough for Group II products 4.

Dry trichlor is listed in Packing Group II, which is why its packs need X or Y 3. The same goes for every product your SDS lists in Group II, including dry dichlor, cal hypo and sodium bisulphate. A Group III product can use a Z pack.

Here is the core of one mark: 3H2/Y28/S/26. On the pack it sits after the UN symbol and before the country and maker codes. The code 3H2 is a plastic jerrican, a can with a removable lid. Y covers Groups II and III. 28 is the maximum gross mass in kg. S means solids. 26 means the pack was made in 2026.

Small retail inner packs can follow a lighter route. BAM's DGG-Info entry for UN 2880 under IMDG 42-24 lists 1 kg per inner pack as the limited-quantity allowance for sea transport 5. Ask your forwarder whether your retail packs qualify. If they do not, the small packs go inside a UN-marked outer box, and you check the letter on that box.

The proof to ask for

Treat a photo of the mark as a start, not the end. The mark only says what the pack design was tested for. You still have to match it to the rule for that chemical and transport mode.

On the China side, the paper to ask for is the customs use-appraisal result for the pack: China customs' finding that the filled pack is fit for those dangerous goods. Past batches of three of our packs have passed this appraisal:

  • The 25 kg open-top plastic jerrican used for trichlor, mark 3H2/Y28/S/26.
  • The 6 kg double-wall carton holding plastic bottles, used for dichlor, mark 4G/Y19/S/26.
  • The 25 kg open-top plastic drum used for bromine tablets, mark 1H2/Y27/S/26.

Each result has its own number and the stamp of the customs office that issued it. You can check that number with that office. But each result covers only the product and packaging batch it names. A past result does not cover your order, so ask for the result issued for your own batch.

Then check four things for each dangerous-goods pack:

  • The use-appraisal result that matches the pack and batch you ordered.
  • The gross weight of a filled pack, product plus packaging, against the number on the mark.
  • A photo of the mark on a filled pack from your order.
  • The UN number and packing group each product will be booked under, from its SDS.

Tip: check the letter before the price. When a supplier sends photos of its packs, look for X or Y in the mark on each Packing Group II pack. You avoid a held shipment over a Z-rated pail.

Moisture, damage, pallets and container space

The pack decides what state the goods arrive in. Put the transit details into one pack spec, so the supplier loads what you priced.

Moisture is the first risk for chlorine tablets and granules. Our standard drums for cal hypo, dichlor and trichlor have inner bags and desiccant, usually two inner bags. A liner is the plastic bag inside a drum or carton. Desiccant is a small pack that soaks up moisture. For other products, ask what the liner is before you order.

How many packs fit in a container changes with the pack you choose, so there is no single figure. Ask for the count for your exact pack, then compare cost per tonne landed.

For the chlorine products, minimum orders and container sharing go together. The minimum for dichlor and trichlor is one full container, and that container can hold both. Cal hypo also starts from one full container. It cannot share a container with dichlor or trichlor. Other products follow their own rules, and our RFQ guide sets out the minimum order and container-sharing rules for each product.

Write the rest into the same spec:

  • Pallet. Say the pallet type, how many layers, and how it is wrapped. Large bags ship on pallets 14.
  • Photos at loading. Before shipping we inspect and send the report with photos or videos 12.
  • Damage terms. Agree in writing what happens with damaged packs. If packs arrive damaged, we refund or replace the damaged goods 12.

Dangerous goods also have to be kept apart in the warehouse. Our guide to storage and shipping rules for oxidizers covers that. For our checks before each load, see how we inspect before loading.

Private-label packs: what to send the factory

For private-label packs, send one approved file per pack. Private label means the pack carries your brand, not the supplier's. We fill small packs to the buyer's specification, so the label and pack details come from you 10.

What to send

  • The label size, measured on the real pack.
  • The final artwork, in the language you sell in.
  • The barcode for each pack size.
  • The net weight as it should be printed.
  • Where the batch number and date go, on the label or on the pack.

Then approve a printed proof before the run.

Your own brand does not raise the minimum. OEM orders have the same minimum as the same product in standard packaging. Agree proof and reprint lead times in the quote.

Retail label or shipping carton

Keep two jobs apart. The retail label is yours. What it must say is set by the product registration in the market where you sell, and you are responsible for it. The shipping carton carries the transport marks. For trichlor the shipping label is the 5.1 Oxidizer label, and it belongs on the shipping pack, not only on the retail label 1.

When the pack spec is settled, put it into your request for quotation; see how to write the pack line in your RFQ.

One pack decision per product, written down

Choose each product's pack by who opens it next. Then let section 14 of each SDS narrow it: Packing Group II products need UN packs marked X or Y, and cal hypo stays out of bags by sea 5. Sodium bisulphate is one of those Packing Group II products, a Class 8 corrosive under our MSDS 7.

Then write it all into one pack spec that the supplier signs off before filling:

  1. Pack type and net weight for each product.
  2. The UN mark letter and the matching use-appraisal result for each dangerous-goods pack.
  3. Liner and desiccant.
  4. Pallet, and the pack count per container for your pack.
  5. Label file and printed proof.

Settle any line the supplier cannot confirm before you place the order.

More on buying from a supplier is in Sourcing & Partnership.

References

  1. NOAA CAMEO Chemicals: UN/NA 2468 (49 CFR 172.101 Hazmat Table entry)
  2. PubChem: Dichloroisocyanuric acid, DOT hazard classification (49 CFR 172)
  3. eCFR: 49 CFR Part 172 Subpart B, Hazardous Materials Table and Special Provisions — Originally published: 2026-10-13; Version read: 2026-10-21
  4. eCFR: 49 CFR 178.503 Marking of packagings
  5. DGG-Info (BAM): UN 2880 Calcium hypochlorite, hydrated, IMDG detail
  6. Kingnod: Sodium bisulphate (pH Minus) product page
  7. Kingnod: Sodium bisulphate MSDS (PH minus MSDS.pdf, product page download)
  8. Kingnod: Calcium hypochlorite product page
  9. Kingnod: DDAC product page
  10. Kingnod: home page and product pages (packing to your specifications, OEM)
  11. Kingnod: Algicide (PQ) product page
  12. Kingnod: About us (Service) and product page quality block
  13. Kingnod: Soda ash (pH Plus) product page
  14. Kingnod: Trichloroisocyanuric acid (TCCA) product page

Find the Right Pool & Spa Products
for Your Market

Get product recommendations, flexible packaging,
and export support tailored to your business.

Welcome to Contact

Your details stay private. Privacy Policy

Request a Sample

Your details stay private. Privacy Policy